
BS4504 PN16 DN65 Steel Plate Flange
Flange with all standards and different type,weld neck flange,slip on flange,blind flange. Flanges and fittings with good quality and competitive price.enough stock .
The Unsung Heroes' Rigorous Selection
In commercial plumbing and industrial pipeline construction, the flange is the silent hero. Whether you're specifying components for a high-rise HVAC system in Lagos, a water treatment plant in Manchester, or a fire-fighting line in the Middle East, "almost right" isn't acceptable. You need a component that respects legacy standards while performing under modern pressures.
Our BS4504 PN16 DN65 Steel Plate Flange is built for engineers and procurement specialists who demand interchangeability, strength, and a perfect fit every time.

Why "BS4504" Still Matters? (Even Though EN1092-1 Exists)
We're often asked why we market under the British Standard instead of the newer European code. The answer is simple: field recognition.
While fully compliant with EN 1092-1, most site crews who worked on pre-2000 infrastructure learned dimensions as "BS4504." By supplying the BS4504 PN16 DN65 Steel Plate Flange, we bridge the gap between legacy drawings and modern precision. No misaligned bolt holes when retrofitting old lines.
This unit is sized at DN65 (≈2.5″ nominal bore), ideal for branch lines and booster pump connections.
Forged vs. Cast – Why We Don't Cut Corners?
We classify this as a Steel Plate Flange, but the manufacturing process is critical.
·Inferior option: Cast iron or cast steel. Cheaper, but may contain porosity (micro air pockets), leading to weeping leaks under vibration.
·Our option: Forged steel.
Billet steel is heated and pressed into shape, aligning the grain structure. This gives our BS4504 PN16 DN65 Steel Plate Flange superior tensile strength to handle 16 bar with a solid safety margin.
We typically stock:
·Carbon Steel (ASTM A105 equivalent) – general service
·Stainless Steel 304/316 – aggressive water or chemical environments
Technical Breakdown – PN16 & DN65 Details
Here's where cheap flanges fail: geometry.
| Parameter | Value | |||
| Pressure rating (PN16) | 16 bar (≈232 psi) at ambient, derates up to 120°C | |||
| Outside Diameter | 185mm | |||
| Pitch Circle Diameter (PCD) | 145mm | |||
| Bolt holes | 4 × 18mm diameter | |||
| Bolting required | M16 bolts (×4), 60–70mm length depending on gasket | |||
| Thickness |
18mm (conforms to Table 16/10 – no "light" versions) |
|||
Why Source This Flange From Us?

CANGZHOU HANGXIN FLANGE CO., LTD. – founded in 1993, specializing in forged flanges and butt-welded pipe fittings for over 30 years.
Strategic Location: Located in Mengcun County – known as the "hometown of elbows and pipe fittings" in China. Only 120km to Xingang Port, 260km to Beijing Capital International Airport.
Manufacturing Capacity: 18,000+ square meters facility with 50 million RMB in fixed assets.
Certified Quality: ISO9001, CE, 3A certified – full traceability to mill certification.
Flat Face vs. Raised Face (Plate Style)
This is a "Plate Flange" (Code 101/112 depending on hub presence).
·Design: Flat disc – not a stress-relieving taper like Weld Neck (Code 111). Slides over the pipe.
·Installation: No complex butt-weld prep. A simple fillet weld on the back (and optionally inside) secures it.
·Sealing: Machined serrated finish (concentric or spiral grooves). With a PN16 gasket (e.g., 3mm EPDM or non-asbestos), the grooves bite into the gasket as you torque the bolts.
Complete Flange Specification Table
Below is the full range of standards, materials, pressures, and sizes we support – all from real factory data. Your BS4504 PN16 DN65 Steel Plate Flange fits directly into this matrix.
|
Items |
Plate, Welding Neck, Slip on, Blind, Socket Welding, Lap joint, Threaded Flange etc. |
|
|
Standard |
ANSI |
ANSI B16.5, ASME B16.47 series A/B |
|
DIN |
Germany 6bar, 10bar, 16bar, 25bar, 40bar |
|
|
GOST |
GOST 12820/12821/12836 |
|
|
EN1092-1 |
EN1092-01/05/11/12/13 |
|
|
JIS |
JIS B 2220-1984, KS B1503, JIS B 2216 |
|
|
BS4504 |
BS4504 BS10 Table D/E |
|
|
Material |
ANSI |
CS A105, S235, Steel 20; SS 304/304L, 316/316L |
|
DIN |
CS RST37.2, S235JRG, P245GH, P250GH; SS 304/304L, 316/316L |
|
|
GOST |
CS Steel 20, 16MN, Q235 |
|
|
EN1092-1 |
CS RST37.2, S235JRG, C22.8 |
|
|
JIS |
SS400, SS 304/304L, 316/316L |
|
|
BS4504 |
CS RST37.2, S235JRG, C22.8; SS 304/304L, 316/316L |
|
|
Pressure |
ANSI |
Class 150, 300, 600, 900, 1500, 2500lbs |
|
DIN |
PN6, PN10, PN16, PN25, PN40 |
|
|
GOST |
PN6, PN10, PN16, PN25, PN40, PN63, PN100 |
|
|
EN1092-1 |
PN6, PN10, PN16, PN25, PN40, PN63, PN100 |
|
|
JIS |
5K, 10K, 16K, 20K, 30K, 40K |
|
|
BS4504 |
PN6, PN10, PN16, PN25, PN40 |
|
|
Size |
ANSI |
1/2" - 80" |
|
DIN |
DN15-DN2000 |
|
|
GOST |
DN15-DN1600 |
|
|
EN1092-1 |
DN15-DN2000 |
|
|
JIS |
15A-1500A |
|
|
BS4504 |
DN15-DN2000 |
|
Trusted by Projects Worldwide
Our BS4504 flanges are already in service across global markets:
Russia – Oil & gas pipeline projects
South Korea – Industrial plant construction
France & Spain – European infrastructure upgrades
Dubai & Middle East – Seawater cooling and HVAC systems
Southeast Asia & Thailand – High-rise building risers
South America – Mining and water treatment facilities
"Same standard, same dimensions – no retrofit surprises."
Application Roadmap – Where DN65 Fits Best
DN65 is the transition point between light commercial and heavy industrial.
Chilled Water Risers
Standard for vertical risers feeding floor manifolds in commercial buildings.
Pump Suction/Discharge
End-suction pumps with 2.5″ outlets pair perfectly.
Skid Systems
PN16 rating allows testing modular pump skids to higher pressures before site installation.
Installation Guide – For Your End-Users
To ensure a leak-free system with your BS4504 Steel Plate Flange:
·Alignment: Slide flange over pipe. Leave a 1.5mm gap at the bottom of the bore. Do not butt pipe tight against the flange face – that prevents proper gasket seating.
·Welding: Tack weld in four places, then apply a continuous fillet weld on the back side (opposite the raised face). For high-vibration areas, add an internal weld.
·Gasket Selection: Use a full-face gasket for flat-faced (FF) flanges, or a standard ring gasket for raised face (RF). Never reuse old gaskets.
·Torquing: Use a calibrated torque wrench (cross-pattern). For M16 bolts on PN16, aim for 80–100 Nm depending on lubricant and gasket material.
Quality Assurance & OEM Options
Off-the-shelf doesn't always fit unusual drawings. We offer full OEM customization for BS4504 flanges.
·Need a non-standard bore for a specific wall thickness?
·Need stainless steel 316L for marine environments?
Honor And Qualification
Official certification, professional after sales service.

3A

CE

ISO9001

ISO9001
Our Manufacturing Capabilities
3500T hydraulic press machine
2500D CNC ring rolling machine
7 forging hammers + 7 large band saws
Maximum flange diameter: 2800mm
Annual output: 13,000 tons of flanges and forged fittings
We accept sample orders to verify quality.
Marking & traceability
Every flange is stamped on the outer rim with BS4504 / PN16 / DN65, material grade, and heat number. Full traceability back to mill certification – satisfies ISO 9001 audit requirements.
Summary
Whether you're retrofitting a Victorian-era building or building a new pumping station, the BS4504 PN16 DN65 Steel Plate Flange delivers strength, weldability, and corrosion resistance. It's a globally recognized standard that connects your pipes safely.
Our Service Commitment
With over 30 years of experience in flange manufacturing and export, we stand behind every product with
Fine quality
100% hydrostatic testing and material certification
Competitive price
Factory-direct pricing with no middlemen
Timely delivery
Ready stock and efficient production scheduling
Good reputation
Trusted by customers in Russia, Korea, France, Dubai, Middle East, Southeast Asia, Spain, Israel, Thailand, and South America
"Fine quality, competitive price, timely delivery – that's our promise."
FAQ – Quick Answers from the Shop Floor
Q: How do I tell which flange type I'm looking at?
A: BS4504 uses a simple numbering system on the rim. Here's what the common codes mean: Code 101 – Standard plate flange for welding (the classic slip-on) Code 105 – Blank flange (used to close off pipe ends) Code 111 – Weld-neck flange (for high-pressure or high-temperature systems) Code 112 – Hubbed slip-on flange Code 113 – Hubbed threaded flange (screws directly onto the pipe – no welding needed)
Q: What's the real-world difference between forged and cast flanges?
A: We covered this earlier, but here's the short version: Forged: Stronger, continuous grain structure, no hidden air pockets. Better for high pressure, high temperature, or safety-critical applications. Cast: Cheaper upfront and easier to shape, but quality depends on the manufacturer. If not done right, you can get pores or tiny cracks. In short: cast for low-risk, low-budget jobs. Forged for everything else.
Q: What should be stamped on a legitimate flange?
A: Manufacturers must stamp traceability info directly on the rim. A proper marking looks like this: BS 4504/101 – PN 16 – DN 100 – Material Grade – Manufacturer Logo – Cast Number If those elements are missing, ask questions before installing.
Q: Can you make custom flanges for my specific drawing?
A: Yes – most flange suppliers (including us) offer OEM services. Send us your drawing, and we'll produce exactly what you need. Sample orders are welcome to verify quality and fit before full production.
Q: How do I install a Slip-On / Plate flange correctly?
A: Straightforward, but don't skip these steps: Slide the flange over the pipe. Leave a small gap (about 1–1.5mm) inside the bore – this helps with alignment. Apply a fillet weld on the back side of the flange to lock it to the pipe. Place a gasket (flat or spiral-wound) between flange faces to create the seal. No complex butt-weld prep needed – that's the beauty of a plate flange.
Ready to Order?
Get a firm quote within 24 hours. Just tell us:
1.Quantity needed
2.Material (Carbon Steel / SS304 / SS316)
3.Any special coating or bore size
Sandy Zhang
Whatsapp:008615127785550
Wechat:0086 15127785550
Email:sandy@yongxingflange.com

"We speak engineering. Send us your drawing – we'll match it exactly."
Hot Tags: bs4504 pn16 dn65 steel plate flange, China bs4504 pn16 dn65 steel plate flange manufacturers, suppliers, factory, steel flange performance testing, steel flange mss certification, steel flange ped certification, steel flange leak testing, steel flange api 615 steel flange, steel flange iec certification
Send Inquiry









