High Pressure 1500lb 2500lb Forged Steel Gate Valve

High Pressure 1500lb 2500lb Forged Steel Gate Valve

Standard export packaging (Wooden cases ,wooden pallet ,plastic bag, polywood case). As Customers' Requirements.

Since the establishment of our company, the primary goal has been to maintain the superior quality, excellent durability and high cost performance of our SR Elbow, Seamless Steel Reducer, GOST 12820-80 Plate Flange. Now we have highly developed devices. You are welcome to contact us anytime! In recent years, we have put a lot of development focus on the promotion of information management and Internet marketing, and we have achieved good results. We have a mature management, quality, technology, warehousing, and delivery system.

Understanding the Class 150 Rating

The Class 150 rating under ASME B16.5 is a commonly specified pressure class for industrial flanges in low-pressure utility systems such as water, air, and cooling lines. The rating is temperature-dependent rather than a fixed limit – carbon steel (A105) handles approximately 19.6 bar at ambient temperature, with pressure capacity decreasing as temperature climbs. This flange type provides reliable sealing and structural integrity, making it a practical choice for engineers specifying components for general service piping across multiple industries. A Class 150 Pressure Flange fits these applications well because its pressure rating comfortably exceeds the typical operating pressures found in building utility system

product-702-527

Working Pressure Range – At -29°C to 38°C: 19.6 bar. At 100°C: 17.7 bar. At 200°C: approximately 15.8 bar. At 300°C: approximately 12.8 bar. 

 

Common Materials

 

Material

Key Properties

Carbon Steel (ASTM A105)

High strength, economical, a common choice

Stainless Steel (304, 316, 316L)

Corrosion-resistant, ideal for chemical and marine environments

 

Applicable Industries 

General industrial piping systems               Water and wastewater treatment

HVAC and building services                  Food and beverage processing                 Fire protection systems

 

Technical Specifications

 

This flange type is manufactured to ASME B16.5, covering NPS 1/2 through NPS 24. The bolt circle, number of bolts, and outer dimensions are standardized across all flange types for a given size.

Class 150 Flange Dimensions (ASME B16.5)

 

NPS

DN

Flange OD (mm)

Thickness (mm)

Bolt Circle (mm)

Bolt Hole Dia (mm)

No. of Bolts

Bolt Dia (inch)

1/2

15

88.9

11.2

60.5

15.7

4

1/2

3/4

20

98.5

12.7

69.9

15.7

4

1/2

1

25

108.0

14.2

79.2

15.7

4

1/2

1-1/4

32

117.5

15.7

88.9

15.7

4

1/2

1-1/2

40

127.0

17.5

98.6

15.7

4

1/2

2

50

152.4

19.1

120.7

19.1

4

5/8

2-1/2

65

177.8

22.4

139.7

19.1

4

5/8

3

80

190.5

23.9

152.4

19.1

4

5/8

4

100

228.6

23.9

190.5

19.1

8

5/8

6

150

279.4

25.4

241.3

22.4

8

3/4

8

200

342.9

28.4

298.5

22.4

8

3/4

10

250

406.4

30.2

362.0

25.4

12

7/8

12

300

482.6

31.8

431.8

25.4

12

7/8

14

350

533.4

35.1

476.3

28.4

12

1

16

400

596.9

36.6

539.8

28.4

16

1

18

450

635.0

39.6

577.9

31.8

16

1-1/8

20

500

698.5

42.9

635.0

31.8

20

1-1/8

24

600

812.8

47.8

749.3

35.1

20

1-1/4

 

 Standard Face Types: Raised Face (RF) is standard for this pressure class, with a height of 1.6 mm (1/16 inch). Ring Joint (RJ) available for certain sizes.

 

Types of Class 150 Flanges

 

Six Configurations for Different Piping Needs

Weld Neck Flange

Designed with a tapered hub for stress distribution. Used in high-critical applications where weld integrity is essential.

Slip On Flange

Slides over the pipe and is welded both inside and outside. Easier to align and suitable for general low-pressure services.

Blind Flange

Solid plate without a bore. Used to seal pipe ends or pressure vessel openings.

Socket Weld Flange

Pipe inserts into the socket and is welded from the outside. Common in smaller-diameter, high-pressure piping.

Threaded Flange

No welding required. Ideal for applications where welding is hazardous or inconvenient.

Lap Joint Flange

Used with a stub end; rotates freely for easy bolt alignment. Suitable for systems requiring frequent disassembly.

 

Application Scenarios
 

Where Class 150 Flanges Are Used Across Industries

Over the years, I have seen these flanges turn up in all sorts of places. In oil and gas, they are the workhorse for utility piping and cooling water-nothing fancy, just reliable. Water treatment plants use them because the pressures are moderate and the cost is right. Chemical plants tend to order stainless steel versions for mild services, which makes sense given the corrosion exposure. Power stations run them in cooling loops and lube oil lines. Shipbuilders fit them to ballast and freshwater systems. And in commercial buildings, they are everywhere in HVAC risers and fire protection lines. The pressure rating is high enough to give you peace of mind, but the weight and cost stay reasonable.

Product Advantages

Why Engineers and Procurement Teams Choose This Flange

Standardised dimensions

Interchangeable with flanges from any ASME B16.5-compliant manufacturer

01

Easy installation

Bolt-on connection requires no special tooling or extensive training

02

Cost-effective for low-pressure systems

Lighter construction than higher-rated flanges means material and cost savings

03

Wide material availability

Supplied in carbon steel, stainless steel, and alloy grades

04

Global compatibility

Recognised and accepted across major industrial markets worldwide

05

Comparison: Class 150 vs Class 300

 

Aspect

Class 150

Class 300

Pressure rating (ambient)

~19.6 bar (285 psi)

~51.1 bar (740 psi)

Flange thickness (NPS 4)

23.9 mm

34.9 mm

Bolt size (NPS 4)

5/8 inch

3/4 inch

Cost

Lower – less material, lighter

Higher – more material, heavier

Typical applications

Water, air, utility services

Steam, process lines, higher pressure systems

 

Decision Guide – Choose Class 150 for general utility services, water, air, and low-pressure applications. Choose Class 300 when system pressure exceeds Class 150 limits at operating temperature, or when future pressure increases are anticipated.

Quality Control & Certification

carbon steel flange raw material block

ISO 9001 – Quality management system ensuring consistent manufacturing processes.

Material Test Certificate (MTC) – Each batch includes chemical analysis and mechanical property verification.

Dimensional Inspection – Bolt circles, thickness, and overall dimensions verified against ASME B16.5.

Pressure Testing – Hydrostatic testing conducted to confirm joint integrity.

Surface Quality Control – Sealing faces inspected to ensure proper gasket seating.

Third-Party Inspection Available – Independent verification upon client request.

 

From where I stand, quality control isn't about ticking boxes or assembling a thick folder of paperwork. It's about what happens two years after installation-when that flange is buried behind insulation, holding pressure day in and day out, and nobody has to think about it because it just works. That is the outcome I care about.

I have seen too many "certified" flanges pass initial inspection with flying colours, only to weep at the gasket face six months into service. The difference often comes down to the surface finish-something that is easy to check with a profilometer but easy to skip when production is running behind schedule. We do not skip it. Every sealing face that leaves our shop gets measured, not just eyeballed. If the roughness number does not fall within our control limits, that flange does not go into the box, regardless of how tight the delivery deadline is.

The Material Test Certificate is another area where I have learned to be particular. It is not enough to have a piece of paper that says the chemistry matches. We pull our own samples from every batch and run our own analysis before we accept material from the mill. I have caught discrepancies that the supplier's certificate did not show-small ones, but small deviations add up when you are dealing with corrosion resistance or weldability.

Third-party inspection is something I welcome rather than tolerate. When a client sends an independent inspector to our shop, I see it as an opportunity, not an inconvenience. Their questions often highlight details we can improve, and their verification gives the client confidence that the product they receive is the product they specified. I have stood beside inspectors from SGS, BV, and TÜV, walking them through our processes, and every time I come away with a clearer sense of what the end-user actually values.

At the end of the day, our ISO9001, CE, and 3A certifications are useful frameworks. They give us structure and accountability. But the real quality control happens in the small decisions made on the shop floor-the decision to re-measure a thread gauge, to re-run a surface finish check, to reject a flange that is "probably fine." Those decisions are what I sign off on, and I do not sign unless I would bolt that flange onto my own piping system.

 

Why Choose Us

1

Factory Direct Supply – We manufacture in-house, controlling quality from raw material to finished product.

2

OEM/ODM Support – Custom dimensions, materials, and thread forms available to your specifications.

3

Fast Delivery – Stock sizes ship within 3–5 working days. Our location 120 km from Xingang Port keeps logistics efficient.

4

Export Experience – Since 1993, we have supplied flanges to clients across Russia, South Korea, France, Dubai, Southeast Asia, Spain, Israel, Thailand, and South America.

5

Certified Quality – ISO9001, CE, and 3A certifications reflect our disciplined quality controls. Certificates available upon request.

I have been answering inquiries from engineers and procurement teams for over twenty years. Most people do not need a sales pitch-they need straight answers about dimensions, lead times, and what can go wrong. That is what I try to give.

 

Frequently Asked Questions

Q1: What does Class 150 mean in flanges?
A Class 150 Pressure Flange refers to a pressure-temperature rating under ASME B16.5, not a fixed pressure. For carbon steel at ambient temperature, it handles approximately 19.6 bar (285 psi). The rating decreases as temperature rises.

 

Q2: What materials are used for these flanges?
Common materials include carbon steel (ASTM A105), stainless steel (304, 316, 316L), and alloy steels. Material selection depends on service conditions such as temperature, pressure, and corrosion exposure.

 

Q3: Can this pressure class be used for high-temperature applications?
Yes, but the pressure rating decreases with temperature. For example, carbon steel Class 150 flanges drop to approximately 12.8 bar at 300°C. Check the ASME B16.5 pressure-temperature table for your specific operating conditions.

 

Q4: Are all Class 150 flanges interchangeable regardless of type?
Yes – all flange types (weld neck, slip-on, blind, socket weld, threaded) share the same outer diameter, bolt circle, and bolting dimensions for a given NPS, ensuring interchangeability.

 

Q5: What is the difference between Class 150 and PN20?
They refer to the same pressure rating. PN20 is the metric designation for this pressure class under EN 1092-1 standards. Both indicate approximately 20 bar rating at ambient temperature.

 

Q6: How do I select the right flange type within this rating?
Start with your installation constraints. Weld neck suits high-stress or cyclic loading. Slip-on offers easier alignment and lower cost. Threaded works where welding is hazardous. Blind seals pipe ends. The Types section above provides a full breakdown. Factor in cost, availability, and future maintenance access when choosing.

 

Q7: What documents accompany shipments of these flanges?
Each shipment includes material test certificates, dimensional inspection reports, and a certificate of conformity. Third-party inspection reports are provided upon request.

 

Q8: Are these flanges compatible with European piping systems?
Yes – Class 150 flanges are recognised under EN 1092-1 as PN20 equivalents and are widely used in European projects that follow ASME or international standards.

 

Request a Quote

 

We respond to inquiries within one business day. For specifications, samples, or quotations, reach out through any channel below.

Tel: +86-317-5298874

Mob: +8618931763322

Email: admin@yongxingflange.com

Add: DingZhuangZi Industrial Zone, Mengcun County, Cangzhou City, Hebei Province, China

Get Drawing Support | Contact for Custom Size | Request a Quote Today

We adhere to the concept of high quality, high requirements and high performance, and provide reliable High Pressure 1500lb 2500lb Forged Steel Gate Valve and services to users. Our company has always adhered to the concept of developing identification equipment that meets the future needs of customers. With strong technical strength and advanced processing technology, our company is committed to providing customers with high-quality personalized products, and has been unanimously recognized by customers.

Hot Tags: class 150 pressure flange, China class 150 pressure flange manufacturers, suppliers, factory, flange fabrication, steel threaded flange price, din steel flange production time, steel flange api 618 steel flange, din steel flange competition, gost flange for residential projects

[[ProKeywords]]

Send Inquiry