DN600 Pn10 Class125 Pn16 Class 150 JIS DIN ANSI Standard Cast/Ductile Iron Wafer Type Dual Plate Check Valve

DN600 Pn10 Class125 Pn16 Class 150 JIS DIN ANSI Standard Cast/Ductile Iron Wafer Type Dual Plate Check Valve

Product Name:Ansi B16 1 Class 125 Flanges An16.5 is the official standard for ANSI Class Pipe Flanges and Flanged Fittings,we product the fllange and pipe fitting

Our company vigorously develops technological innovation, improves the research and development capabilities of new Carbon Steel Socket, Class 1500 High Pressure Flange, Steel Flange Plate, and introduces equipment of international cutting-edge. Enterprise managers must maintain dedicated to their jobs, running the enterprise wholeheartedly, and strict testing is required for each listed product. Our professional technological team will be wholeheartedly at your services. They're going to allow you to get complete acknowledge about our items and make a satisfied negotiation. We take 'innovation, fashion, vitality' as the brand connotation, 'Initial & Inspire' as the research and development policy.

Product Name:Ansi B16 1 Class 125 Flanges

An16.5 is the official standard for ANSI Class Pipe Flanges and Flanged Fittings,

applied specifically to those made from cast or forged materials, as well as blind flanges and some reducing flanges crafted in cast, forged, or plate.

 

size

The size of all flange fittings and predetermined flanges indicates nominal

The pipe diameter of the port. Standard reducing elbows have the same

The face-to-face size is the normal elbow with the largest straight size.

 

Tolerance range

The test limit is plus or minus 1

/ 32 inches (1 mm) should be allowed

All dimensions from the center to the contact surface, the largest dimension includes

10 NPS (250 DN); plus or minus 1

/16 inch (1.5mm) when the size is greater than 10

NPS (250 DN). Test limit plus or minus 1

/16 inch (1.5mm) should

Allow the contact surface size on all contact surfaces to be

The size does not exceed 10 NPS (250 DN); plus or minus 1

/ 8 inches (3 mm)

The size is greater than 10 NPS (250 DN). Largest opening in accessories

Control the tolerances to be applied to all openings

 

Flange material restrictions
1) Flanges and flange accessories should be castings, forgings or plates.
2) Bolt material shall comply with ASME B16.5, Table 1B.
3) Flanges that require galvanizing should be galvanized using the hot-dip galvanizing process in compliance with ASTM A 153. The flange surface should be properly protected during the galvanizing process to avoid surface irregularities that may lead to leakage during flange assembly.
4) Cast Iron Flanges: Gray cast iron flanges shall not be used for process piping within the scope of any factory battery. The only exception is for use with approved fire protection systems. The material shall conform to ASTM A 126 Class B.
5) Ductile Iron Flanges: Ductile iron flanges can be used in proprietary systems, such as plastic lined steel pipes, as backup flanges for lap joints.
6) ASME B16.1 Grade 125 and 250 cast iron flanges can be matched with ASME B 16.5 Grade 150 and 300 steel flanges respectively. However, care should be taken to ensure that flat cast iron flanges can only mate with flat steel flanges and vice versa.
7) Carbon steel flange: Carbon steel flange shall not be used in environments exceeding 425°C.
8) General Purpose: Standard carbon steel material shall be ASTM A 105. Standard materials should be used between -29 °C and 425 °C. Companies may specify additional requirements such as normalizing. These special requirements should be added to the purchasing instructions.
9) Low-temperature carbon steel flanges used for -29°C to -45°C should comply with the impact test requirements of SES P02-S01. ASTM A 350-LF2 shall be the standard material for this service.
10) Low and Medium Alloy Steel Flanges The material for low alloy steel flanges (1 1/4 Cr -1/2 Mo) shall be ASTM A 182-F11. The material for intermediate alloy steel flanges (5 Cr – 1/2 Mo) shall be ASTM A 182-F5.

 

Production Equipment

our company equips hydraulic press machine of 3500T,CNC ring rolling machine of 2500D,7 forging hammers, 7 large bandsaw,lathes and drillers for the making of forged flanges at maximum diameter of 2800MM . Our annual output for flange and forged fittings is 13000 tons. Advanced production lines enable us to meet customers different requirements and supply quality products

 

Production Market

Russia, South Korea, France,Dubai ,Middle East,Southeast Asia,Spain, Israel, Thailand,South America etc.

1)

We make continuous efforts to really improve the quality of DN600 Pn10 Class125 Pn16 Class 150 JIS DIN ANSI Standard Cast/Ductile Iron Wafer Type Dual Plate Check Valve and effectively drive the improvement of the quality of domestic related products. We have a scientific management system, a high-quality workforce, advanced technology and equipment, and have become a reliable strategic partner chosen by many customers and suppliers. We have been adhering to the business philosophy of 'honesty-based, quality first, service innovation', and the service concept of 'meeting requirements of customer as our most important responsibility, pursuing quality for survival and reputation for development', and striving to create a high-quality enterprise brand of the new era.

Hot Tags: ansi b16 1 class 125 flanges, China ansi b16 1 class 125 flanges manufacturers, suppliers, factory, installation steel flange, gost flange for offshore platforms, SR Elbow, steel flange function testing, flange reliability, flange performance

[[ProKeywords]]

Send Inquiry