DN40-DN1200 5K 10K DIN ANSI Standard Cast/Ductile Iron Wafer Type Dual Plate Check Valve

DN40-DN1200 5K 10K DIN ANSI Standard Cast/Ductile Iron Wafer Type Dual Plate Check Valve

Product Name:Ansi B16 1 Class 125 Flanges An16.5 is the official standard for ANSI Class Pipe Flanges and Flanged Fittings,we product the fllange and pipe fitting

We have unique insight and abundant practical experience in the field of Class 300 Lap Joint Flange, EN 1092-1 PN16 Steel Flange, Steel Flange Plate. We guarantee quality and diversity. We believe that our products can get your 100% trust, and through our efforts to help you achieve success. We are committed to improving leadership, execution and cohesion with culture, promoting productivity with culture, and improving the overall development level of the company with soft power. Our company has seen a lot of changes in the past years of business. Our products are exported to many countries and regions for their excellent performance and good reputation, and we have established long-term and stable cooperation relationships with many well-known enterprises abroad.

Product Name:Ansi B16 1 Class 125 Flanges

An16.5 is the official standard for ANSI Class Pipe Flanges and Flanged Fittings,

applied specifically to those made from cast or forged materials, as well as blind flanges and some reducing flanges crafted in cast, forged, or plate.

 

size

The size of all flange fittings and predetermined flanges indicates nominal

The pipe diameter of the port. Standard reducing elbows have the same

The face-to-face size is the normal elbow with the largest straight size.

 

Tolerance range

The test limit is plus or minus 1

/ 32 inches (1 mm) should be allowed

All dimensions from the center to the contact surface, the largest dimension includes

10 NPS (250 DN); plus or minus 1

/16 inch (1.5mm) when the size is greater than 10

NPS (250 DN). Test limit plus or minus 1

/16 inch (1.5mm) should

Allow the contact surface size on all contact surfaces to be

The size does not exceed 10 NPS (250 DN); plus or minus 1

/ 8 inches (3 mm)

The size is greater than 10 NPS (250 DN). Largest opening in accessories

Control the tolerances to be applied to all openings

 

Flange material restrictions
1) Flanges and flange accessories should be castings, forgings or plates.
2) Bolt material shall comply with ASME B16.5, Table 1B.
3) Flanges that require galvanizing should be galvanized using the hot-dip galvanizing process in compliance with ASTM A 153. The flange surface should be properly protected during the galvanizing process to avoid surface irregularities that may lead to leakage during flange assembly.
4) Cast Iron Flanges: Gray cast iron flanges shall not be used for process piping within the scope of any factory battery. The only exception is for use with approved fire protection systems. The material shall conform to ASTM A 126 Class B.
5) Ductile Iron Flanges: Ductile iron flanges can be used in proprietary systems, such as plastic lined steel pipes, as backup flanges for lap joints.
6) ASME B16.1 Grade 125 and 250 cast iron flanges can be matched with ASME B 16.5 Grade 150 and 300 steel flanges respectively. However, care should be taken to ensure that flat cast iron flanges can only mate with flat steel flanges and vice versa.
7) Carbon steel flange: Carbon steel flange shall not be used in environments exceeding 425°C.
8) General Purpose: Standard carbon steel material shall be ASTM A 105. Standard materials should be used between -29 °C and 425 °C. Companies may specify additional requirements such as normalizing. These special requirements should be added to the purchasing instructions.
9) Low-temperature carbon steel flanges used for -29°C to -45°C should comply with the impact test requirements of SES P02-S01. ASTM A 350-LF2 shall be the standard material for this service.
10) Low and Medium Alloy Steel Flanges The material for low alloy steel flanges (1 1/4 Cr -1/2 Mo) shall be ASTM A 182-F11. The material for intermediate alloy steel flanges (5 Cr – 1/2 Mo) shall be ASTM A 182-F5.

 

Production Equipment

our company equips hydraulic press machine of 3500T,CNC ring rolling machine of 2500D,7 forging hammers, 7 large bandsaw,lathes and drillers for the making of forged flanges at maximum diameter of 2800MM . Our annual output for flange and forged fittings is 13000 tons. Advanced production lines enable us to meet customers different requirements and supply quality products

 

Production Market

Russia, South Korea, France,Dubai ,Middle East,Southeast Asia,Spain, Israel, Thailand,South America etc.

1)

We rely on high-quality staff, high-precision production equipment and strict testing methods to produce high-quality DN40-DN1200 5K 10K DIN ANSI Standard Cast/Ductile Iron Wafer Type Dual Plate Check Valve. Teamwork is encouraged at all levels with regular campaigns. While we are putting quality first, we have also been providing honest service. For many years, we have been committed to customer satisfaction and strive to build our enterprise with our integrity and sincerity.

Hot Tags: ansi b16 1 class 125 flanges, China ansi b16 1 class 125 flanges manufacturers, suppliers, factory, gost flange for reactors, steel flange aga certification, gost flange for reliability, gost flange for perimeter security, gost flange for residential projects, gost flange sealing

[[ProKeywords]]

Send Inquiry